ok everyone in my 63 with straight axle I have a cpp box DRILL three hole clock the steering box to proper angle and it bolts right in connect with and universal joint and all GOOD!!

I have a 63 kept the straight axle and put a ccp 400 box in works great .give them a call

61 to 64 are the same 65 and 66 are different the shift tubes are different and the whole column is shorter later columns use a nylon spacers and earlier ones use steel .shift tubes are cut to size and fitted getting the right size is a trial and fit process .

looking into a Dakota swap wondering what the total cost finished would be using a industrial chassis crossmember what is the cost of A arms and othe junk yards and how much does it drop the truck .I have a 63 like max .

Thanks

I installed new vent window frames with new rubbers from carpenters .The problem is the window will not close all the way to shut .I don't know how to solve this problem .any help would be great thks

thanks guys truck has a new wiring harness but I will check all the sockets also just put a new turn signal switch so I will check its not hitting something on the column thanks again

turn signal keeps popping fuses that means ground short correct any help would be great thks

the pump is NOT in the kit I have a 289 in my truck with sanderson block hugger headers and got the pump and bracket from toms bronco parts 800 749 5028 for 200.00 I don't know what motor you have in your truck .it did not include the hoses .I got the hoses from CPP .but they come in the kit .My tru...

yes correct but forget the rag joint and just get a dd universal to fit the box and mill /grind your oem steering shat to fit the universal and also go to a bearing shop and get a bearing to fit your shift tube with a id that fits your steering shaft . I had someone turn down to universal joint so i...

is it possible to just replace the rubber on the divison bar next to the vent window or do you have the replace the whole bar thks

just buy the whole kit from classic performance it says till 60 but works in our trucks too .

For power steering go with a ccp box it BOLTS IN to standard location and put a Saginaw power steering box with a fluid reducer on it that's what I have on my 63 and it works great
Used a universal joint to hook the steering shat to box and be done !!

I am putting my steering back on and on the back side of the wheel is the piece that cancels the turn signals after you turn them on ..My question is what position does it go on ie at 3,6 ,12 its the little spring metal piece on the back of the wheel ok thks

Thanks everyone thought I would have to buy a new switch again thanks

I am replacing my turn signal switch on my 63 the switch has 8 wires two of which go to the horn contacts .originally there way only one so i CUT one contact off and installed the switch .Does it matter that it only has ONE contact now and do i need to order a new switch and keep the switch intact ....

I have a 289 in my 63 and I used tube style mounts its like a cross bar with flanges on the end much easier to use speedway has them Also stiffens up the frame .just get the correct drop for the trans .

I just put 15 on mine works great

I have plenty of legroom in my 63 with a 14 inch steering wheel I am looking to purchase a 66 or so fairlane or galaxie I know that the galaxie is a bigger car so leaning toward the fairlane also want it to be a convertible since I live in florida want just a nice daily driver what price should I be...

Well finally got around to installing my new 5000 series ccp power steering box and got rid my Toyota box All I can say is that the ccp box fits great and works like it should the only problem I had is the ford steering pump didn't have enough power to make it work so we went to a Saginaw pump and e...

have a 63 stepside with 289 3 speed and 2.75 rear gears what is the towing ability of my truck would like to tow a vintage boat or camper like airstream of something similar thks