I see some of your pricing info is a little out of date , what is the cost now, and are
they available now without the console ?
thanks Joe Mac

should try to find the optional passenger side wiper LOL
enjoy the truck like every day is your last

you can use Loctite 640 or 660 retaining compound to reinsert your bearing race . it is made for press fit or slip fit
and provides a sheer strength of 4000 lbs

LOCTITE makes a product to to use in the bearing races to tighten them up
I used it in a king pin bushing I couldn't stop from turning trying to ream it
works great I will post the number and type when I go out to the shop

Here are a few pictures of the truck being painted . truck is still not back together, now I have decided to repaint the rad support and inner fenders , repaint the steering column, new carpet and head liner

Hey guy's Been a while since I have been here. Was actually surprised my info and password still worked. I still have my 64,actually just had it repainted ,same colour's but base- clear this time around. This is the 3rd time it has been repainted, once in 1988 again in 1999 and now in 2014. Man I'm ...

i have been looking for a c6 transmission now somebody has told me that a column shiffted transmission is different from a floor shifted transmission i am told that p r n d 2 1 are reversed on the transmission so if you use a floor shifted transmission in a column shift vehicle 1 will be where p sho...

have you got the proportioning valve plumbed int the rear brake line also you might require the use of pressure risidual valves 10lbs valve on rear line and 2lbs valve on front line with the proportioning valve on the back brake line.

thanks for the quick reply and the link gene
seems to me a bad idea judging the responses here.bought a set of tri bars for my 34 but dont like the way they look on it figuired they looked ok on my truck but who needs the greif thanks again for the great info at slick 60's

hi guys i want to install h4 halogen headlights in my truck but i seem to remember reading here that the wiring isnt up to parr to handle this and you needed to add a few things in order to do it if any one wishes to share that info again it would be greatly appreciated checked the hints and tips pa...

i use both the idiot light and a mechanical gauge with a t fitting broke the oil pump drive once in my fe by the time i noticed the gauge the damage was done my engine builder an old timer race car driver suggested this as you will notice the light immediattly when it loses pressure

i use wooden clothes pin or wooden wedges to place in between each coil wind to remove or install hood or clutch springs if already installed on vehicle use channel lock plyers to wedge clothes pins inbetween coils alternating from side to side to install a spring you can bend the spring side to sid...

i would definetly check your firing order on the cap and plugs and if your wires are old change them as well fe ,,,,,,,,,,,,,,,,,,,,s are bad for arcing between the wires if the wires are bad or run over top of each other also i would run a new hot ignition wire to a ballist resister and then to the...

on my 64 i removed the straight axle and put 66 twin i beam under the front end chevy s 10 power steering box late model disk brakes removed the 292 and granny 3 speed in favour of 390 and toploader 4 speed 94 ford e 250 van aluminium driveshaft (bolts right in) kenwood am/fm cd new 66 outer chromea...

check your king pins as well for wear and make sure they are greased well also have you done any mods to the truck raise the rear lower the front if the king pins get standing to straight up and down instead of leaning back this will also make the truck hard to steer

my engine builder opened and polished the drain holes on the back of the heads where the bolt passes tru and restrictes the flow and tapped the oil holes and used set screws with a hole drilled thru it can run the engine with no valve covers and no back up of oil at the drain holes my builder is clo...

bathroom scales will work fine

soda will not remove rust and leaves metal to smooth for paint i stripped the paint off mine with a razor blade down to the primer then sanding was a breeze then you only have to blast the rust

i know we all try to save money by doing our own work but some things you just got to bite the bullit and and leave to the pros those who know what they are doing can do it quite cost effectivelly when i do any blasting at home i will hook my small compressor for running my carpenter type air tools ...

johnny still not ready to give up on horsepower torque and poor fuel economy yet second child hood thing i think??? just glad i dont live where i could drive all year round i would be living in the truck lol