I know it back from the dead... is there a wiring daigram for this set-up? I have a line on a set of motors, and would like a little more detail on wiring.

Cedar Lake, IN

this might not be too bad to do... if you look close the mirror creates and area deep enough to clear the hinges in the door... I have been working out the logistics in this mod for the last few days after reading a how to on removing the vent window... I figured by creating a sq. off edge around th...

The crown Vic set-up out here is $650 for everything between the wheels... a good price considering the little work it requires compared to other set-ups...

so the fenders bolt up fine, its just the inner fenders that have the problem... and the Radiator support is different... I don't plan on running the stock inner fenders so thats not an issue (Air ride with CV front end) and the radiator is going to be replaced as well so looks like I need to order ...

I realize this is an broker truck... meaning the owner probably let it go for the real value and the broker is trying to mark it up. Like the color, but not the flames... i like the look of the truck showing what a owner can do... Notice the blue paint on the air duct... owner type mistakes... skipp...

I love it... the smooth inlaid front bumper is awesome, great work. The doors are very kewl with the arm rest molded in. I like that the air is in the dash and not just some crappy under dash add on. I enjoy the air cleaner assembly. And I love the fact that I can't see all kinds of color behind the...

I am going to go the rechrome route with mine... that was I can weld the bolts on, grind off the heads and rechome it as a smooth bumper... no one seem to offer one that I have found.

I have a lot of work to get the floor, kicks, and rockers useable on my truck... I wanted to know what pard of the rock is handled by the rocker patch from LMC Truck? is it just the curve.

right in my area... is there a website or anything that gives times and location... other wise post the form somewhere and put up a link... please...

On my '66 its brights...

where did he find these... there has to be more info on this truck... what IFS does it have... How much was it body dropped... what offset are the wheels...

That thing is so awesome...

it's about what we have going on out here... except mine will have a built 302

it's about right.... the trans tunnel is also pushed to the passenger side. This give the driver more room.

if you buy some of the new replacement models they have a load equalizer (resistor) built in to the light, this makes the car see the same load as a regular bulb. I know the APC ones do (though I am not a fan of most their products).

To be honest I have no idea how we are going to do the tonneau. Some of the ideas that have been kicked around is to use a current long bed f100 tonneau and cut and remold the side to allow it to fit flush... Eric at Wire Nutwill have to figure it out... he's done full fiberglass tonneau's with inte...

The color is a dark gun metal and copper... The dash will be the same, with a chrome column and a gunmetal steering wheel and a copper horn ring. The seat is a subject of debate... I haven't been able to find any fabric close to the copper color I am using... Thoughts are that we can do the seat in ...

I added the rendering of the 66 long bed custom cab to my gallery, let me know what you think... Mods - Shaved handles, locks, gas fill, emblems - Roll pan - recessed front bumper - billet inserts for grill - 20" rims on all corners - CV Front end - IDIDIT tilt column - Custom gauge panel - Bui...

Are you going with full door panels and what not... anything different then the stock style layout? Just trying to see what other people are up to while I start planning mine out...

I have a set of the GlassMan dvd's, they walk you through everything... it's a 9 dvd's covering everything including gauge pods, sub boxes, kick panels, rear deck... the list goes on and on... don't know if there still available, as the site doesn't seem to have the store running any longer though.