BUMP...Need a 62 Auto shift rod?

I have a 62 Uni, I bought an Auto column and gear box assembly, I am about to swap in a 390 Automatic, Does anyone have a Shift rod? Thanx, Steve

I had bad luck with the window felts, none of the clips lined up with the holes...I cannot remember who made them, but they are common, I am looking for another set, I'll keep watching out....

Yes, I have seen these brackets, was hoping all Ford was attainable...I was thinking 65 factory engine mounts and then the aftermarket trans mount.....

Hi, I have a 62 Unibody with a Y-block and 3 speed manual...I really want to put in an FE with Auto trans, I am getting my hands on a 62 T-bird 390 with MX (cruise-0-matic)trans...Does any one have original frame mounts and a trans crossmember, possibly looking for a shift link, I already bought an ...

I am here and watching with anticipation, would love to mate up the ZF to a FE. I do not have any pics for you though.....

Hi, I need to change my speedo gear on both the tranny output shaft and the cable end, Will the tranny tail housing just pull off and the mainshaft stays, or do I try to pull it all at once? Thanx in advance....Steve

Ok, I installed all new weatherstripping, man, that stuff fits bad (on lower door edge, it doesn't even follow the curve and it doesn't even roll up the rear edge)...any hints, or a better manufacturer? 62 Merc Uni....

I have 1 perfect one and one the rusted away to nothing also....

Cmon, anyone have one, lots of you guys have put the tanks in the rear, should be lots of these brackets layin around, PM me.....

Hi, I have a 62 Merc. Uni, needing 1 lower fuel tank bracket, it bolts on the bottom and the fuel tank slips into the clip part. If someone has a good used or point me where to buy. Thanx, Steve

As far as my understanding, there is no performance benefit, The S intake was just on GT 390 and the restorers need it as such. I am on many FE forums and nobody wants them except for a resto or 2 . I would personally pick up any aftermarket aluminum manifold and use it anytime if performance is the...

I have seen those corner pieces for sale once in a while on ebay, keep looking, I'd drill out all spot welds, straighten everything out and weld back on the new corner.

I am trying to get a quote for the windshield, just checking, I have a 62 Mercury Uni M250....same as any F100?

There is a windshield in the truck, but clear siliconed in and a big rock chip, the guy gave me some original chrome, So far, I want the original look, green tint glass....leaning towards an all rubber seal to match the rear window....I will clean up the glass recessed area, as it's getting some bod...

Not sure where, need something within 3 months.....probably gonna go without chrome?

Hi, well I need to replace my front windshield, So I see repop windshields, not too bad, but which one, the tint on top or the greenish tint, which do you guys use? Also, The gaskets, I see one with and one without the chrome strip, which one, I have a strippy 62 uni, but the guy gave me some trim, ...

I have a 62 uni, Who sells the foam? I see seat covers galore.

Mine says "2RW". It's a 62 Thanks for the information... Nice to have My truck looks like this. https://goo.gl/photos/HiJ1uN8TD2x4NZmv7 Near as I can tell it's original, under hood is white too. Nic I have the Brother to your truck, Mine is near Identical, M250. I could use that Hubcap......

Mine says "2RW". It's a 62 Thanks for the information... Nice to have My truck looks like this. https://goo.gl/photos/HiJ1uN8TD2x4NZmv7 Near as I can tell it's original, under hood is white too. Nic I have the Brother to your truck, Mine is near Identical, M250. I could use that Hubcap......