This is a 67 and an F600, but a Napco according to the seller.

Maybe give them a call, could be a source of info for you?

https://norfolk.craigslist.org/cto/d/vi ... 05093.html

UPDATE: Located parts at salvage yard, already uncoupled from the engine. In my garage now for cleanup and installation. Looking to buy power steering pump bracket(s) for early to mid 1980's Ford E150 Van with the 300 inline six. These should have been supplied with a Saginaw pump from the factory. ...

Thanks, I'm not interested in political correctness, just want the right stuff in there to keep the pump doing what it's supposed to do.

When reworking the 65 4x4, 300 six, I used a power steering pump that I picked up with the brackets to mount to the inline six. It's never worked. I have a replacement from the local chain auto parts supply. I don't have an owners manual for a 78 F150, which the pump cross refences to, and online se...

That fellow is a phenomenal guitar player, actually a certified guitar player, as bestowed by the late Chet Atkins. I've been following some of his online guitar lessons. A true artist for sure, right hand thumb keeping a bass rythym going while other right hand fingers playing a lead melody. Switch...

Here is a link to summit for a walker y pipe that ties both of your split manifolds into one pipe. This would be for a single exhaust, unless you split it from the end of the y pipe back out to two. https://www.summitracing.com/parts/wlk-45166 I'm not sure I have seen an intermediate pipe for dual e...

Tell us more about the carb and propane setup. Is that offenhauser intake a dual plane or single? Can the engine run on both gasoline and propane, in other words can you use a shut off valve and cutoff gasoline and turn on propane, then switch the other way? I like what you are putting together. Bra...

This might not be everyone's cup of tea. I stumbled on to him on a local radio station, then began listening to the podcasts during drive to and from work, after the radio station changed format. We never bought any kit or products, just listened, looked online at the steps, and concepts. My wife go...

Hello,

Edited post.

http://www.garysgaragemahal.com/speedom ... gears.html

This site may be more helpful, showing rear axle ratio, tire size, transmission, speedo gears needed.

I can't help with the number of bolts, both my np435's had a transfer case with them.

Bradshaw

I just went through this with a 1973 300 six block, small block bellhousing from a 65, np435 4 speed transmission from a 78 F150 4x4. The old flywheel had cracks in it. I replaced it with a new 164 tooth flywheel, new clutch and pressure plate. Used original stater, all works fine.

I'm not familiar with this custom cab dash insert. What are the two small lamps between the speedometer cluster and each of the two side gauges? Are they turn signal indicators?

That's looking very cool.

I like that anvil shifter knob. Undoubtedly you made that!

Bradshaw

I hope you can find some in your part of the world. I've located a pair, but cant get it all worked out to get them from point a to point b. From what I have observed, it appears one could use the smaller fender, trim away the lower stamping and roll the edge under to create the same large opening f...

Try this link.

https://www.prothanesuspensionparts.com/6105

Scroll to bottom, it shows other years and 66 4x4 is listed as compatible.

Good luck, Bradshaw

Chased down the gremlins with the brake and turn signals. It was a combination of wires in the wrong socket from the turn signal switch AND the pressure switch for the brakes was bad. Emergency flashers working with a piece of gum foil wrapped around the 2 amp instrument fuse till I can get one tomo...

Try this link to formulas and a calculator.

Scroll to the top of the page at link below for formulas and calculator.

http://www.tciauto.com/tc/speedometer-g ... ator/#FORD

Slowly working at getting it back together. Spent some time trying to get the bed leveled and aligned with the cab. https://preview.ibb.co/mm3sjS/IMG_20180507_182102257.jpg Got the aluminum grill back in temporarily till I get the metal grill repaired and painted. https://preview.ibb.co/nFwCjS/IMG_2...

The truck I'm working on is a 4x4 with a mid 70's 4x4 frame. The truck had either 352 or 360 V8 and I swapped in a 300 straight six. I used the same z-bar that was with the V8 when installing the 300. The ball that screws into the block was already in the 300 and I've sold the V8 so I don't know if ...

Today I got the vacuum gauge plumbed into the manifold vacuum source. Then made some adjustments to the carburetor according to the manufacturer instructions. The engine is pulling 18" of vacuum at 750 rpm. Throttle response is great with no stumbling. I still need to get the air cleaner fixed ...

Thanks Bill. I picked up a timing light from a CL ad close by for $25, made by Mac tools. Set the timing with vacuum source to carb disconnected and plugged. Adjusted fuel level in fuel bowls. Picked up fittings to tie the vacuum gauge in the dash into the manifold vacuum source. After connecting th...