1.ok antenna seal to cab? same deal as the wipers?
2.is using the fresh air doors in the kick panel important?
3. who do you guys and gals use for the headliner? would like to do a full wrap
4.the blinker i guess buckets in the front are they installed from the front or back ?
5. does anyone know the bolt size for the seats?
6.got my hood alighed good but when i close the back has to be pushed down? are the shot?
7..i would post pictures from photo-bucket but can't figure it out
thanks guys and gals your help is so appreciated
alright more assembley questions 1966 ford
-
- Posts: 12
- Joined: May 7, 2016, 8:54 pm
- Location: Vancouver WA
Re: alright more assembley questions 1966 ford
You can get the wiper seals from any of the vendors. Tom is a good one you can trust him.
Its not a must to use the fresh air vents, but it sure is nice in the summer.
Again you can get a new headliner.
I did my truck but don't remember now if they come out from the front or the rear, guess I could go look.
Not sure of bolt size for the seats, would have to look. But I would guess it is a 1/2 " or 9/16'
Try putting a couple of washers under the front where the hood to hinge bolts go. Don't ask me why it works but it does.
Click on the image you want to post, when it comes up click on the box to the right that has IMG on it. It should say copied when you do. Go back to forum that you want to post on and hit CTRL key and the V key at the same time. Then click on preview and if the picture is like you want it click on submit.
Its not a must to use the fresh air vents, but it sure is nice in the summer.
Again you can get a new headliner.
I did my truck but don't remember now if they come out from the front or the rear, guess I could go look.
Not sure of bolt size for the seats, would have to look. But I would guess it is a 1/2 " or 9/16'
Try putting a couple of washers under the front where the hood to hinge bolts go. Don't ask me why it works but it does.
Click on the image you want to post, when it comes up click on the box to the right that has IMG on it. It should say copied when you do. Go back to forum that you want to post on and hit CTRL key and the V key at the same time. Then click on preview and if the picture is like you want it click on submit.
Last edited by Michelle on January 29, 2017, 11:06 am, edited 2 times in total.
Michelle
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
-
- Posts: 932
- Joined: January 10, 2011, 4:58 pm
- Location: High Springs Florida
Re: alright more assembley questions 1966 ford
Fiberglass is also available from Irl in Oklahoma.
Re: alright more assembley questions 1966 ford
Question 4: Turn lamp buckets screw in from the front.
"Don't piss down my back and tell me it's raining" - Fletcher from The Outlaw Josie Wales
"We all go a little mad sometimes" - Norman Bates
"We all go a little mad sometimes" - Norman Bates
-
- Posts: 906
- Joined: August 12, 2009, 9:44 am
- Location: Ohio
Re: alright more assembley questions 1966 ford
1.ok antenna seal to cab? same deal as the wipers?
This is a form seal with a lip around the edge.
2.is using the fresh air doors in the kick panel important?
They bring in a lot of air at your feet. Can get hot if you have not insulated the floor and firewall.
3. who do you guys and gals use for the headliner? would like to do a full wrap
4.the blinker i guess buckets in the front are they installed from the front or back ?
The are attached with screws from the front.
5. does anyone know the bolt size for the seats?
6.got my hood alighed good but when i close the back has to be pushed down? are the shot?
Springs might be weak. Hood can also be tweeked. You can use a plastic wedge (available as shims for construction) with the larger end towards the front between the hood and hinge to lower the back.
7..i would post pictures from photo-bucket but c
This is a form seal with a lip around the edge.
2.is using the fresh air doors in the kick panel important?
They bring in a lot of air at your feet. Can get hot if you have not insulated the floor and firewall.
3. who do you guys and gals use for the headliner? would like to do a full wrap
4.the blinker i guess buckets in the front are they installed from the front or back ?
The are attached with screws from the front.
5. does anyone know the bolt size for the seats?
6.got my hood alighed good but when i close the back has to be pushed down? are the shot?
Springs might be weak. Hood can also be tweeked. You can use a plastic wedge (available as shims for construction) with the larger end towards the front between the hood and hinge to lower the back.
7..i would post pictures from photo-bucket but c
-
- Posts: 932
- Joined: January 10, 2011, 4:58 pm
- Location: High Springs Florida
Re: alright more assembley questions 1966 ford
viewtopic.php?f=5&t=25049&p=224138&hili ... ge#p224138
hood fix #6, dont know where pictures went
Danny
hood fix #6, dont know where pictures went
Danny